If you have been reading about secondary drying and want a single page that covers the useful parts, this is it: definitions, context, how it is studied, and the questions that come up repeatedly.
Updated 2025-09-13. Numbers and descriptions here follow the published literature rather than marketing material.
The physical chemistry of freezing influences whether a formulation forms an amorphous glass or a crystalline solid. Amorphous systems can collapse if product temperature rises above the glass transition temperature of the freeze concentrate. Crystalline systems may show eutectic melting, where ice and solute melt together at a fixed temperature. Formulators add bulking agents, lyoprotectants, and buffers to preserve structure and biological activity. The optimum cycle keeps product temperature below critical thresholds during primary drying while allowing efficient sublimation.
Lyophilization is a dehydration process that removes water from a frozen material by sublimation under low pressure. The material is first frozen so that water becomes ice; then the surrounding pressure is lowered below the vapor pressure of ice. Heat is applied gently so ice changes directly to vapor without passing through a bulk liquid phase. The vapor is collected on a cold condenser, leaving a dry porous matrix. This process differs from simple evaporation because the material remains frozen during the main drying stage.
The process usually has three stages: freezing, primary drying, and secondary drying. Freezing sets the ice crystal structure and can determine pore size in the final cake. Primary drying removes free ice by sublimation at low pressure and low shelf temperature. Secondary drying removes bound water by raising the shelf temperature, although some water may remain as part of the solid. Cycle parameters depend on formulation, fill volume, vial type, and equipment performance.
Equipment for lyophilization includes a vacuum chamber, temperature-controlled shelves, a condenser, and a vacuum pump. A refrigeration system cools the shelves and condenser below the product's freezing point. Process monitoring often uses Pirani and capacitance manometers, thermocouples, and resistance sensors. Cycle development balances product quality with time and energy use. Some products are annealed during freezing to improve crystallization of bulking agents. Open questions remain about scaling cycles between laboratory, pilot, and production freeze-dryers.
Lyophilization, also called freeze-drying, removes water from a frozen material by sublimation under reduced pressure. The process begins with freezing, which converts free water into ice and may also produce a glassy phase. Primary drying then lowers chamber pressure so ice sublimes directly to vapor without passing through a liquid stage. Secondary drying raises the temperature modestly to remove bound water. The result is a porous, dry solid that usually reconstitutes quickly. Each stage influences pore structure, residual moisture, and stability.
The physics of lyophilization depends on phase boundaries and heat and mass transfer. During primary drying, heat supplied to the product must equal the latent heat of sublimation, while water vapor moves through the drying cake to the condenser. If shelf temperature or pressure is set too high, the ice front can exceed the collapse temperature, causing meltback or pore collapse. If conditions are too cold, drying slows and costs rise. Formulation excipients, vial geometry, and freezing rate alter these limits.
| Property | Value | Notes |
|---|---|---|
| Common synonyms | Freeze-drying, lyophilisation | Lyophilisation is the British spelling; the process is not simple evaporation. |
| Primary drying pressure | 0.05–0.3 mbar | Pressure must remain below the vapor pressure of ice at the product temperature. |
| Sublimation temperature | Below 0 °C | Ice changes directly to vapor while the product remains frozen. |
| Typical shelf temperature | −40 to −10 °C | Exact setting depends on formulation critical temperature and equipment. |
| Cycle duration | 12–72 hours | Time varies with fill volume, formulation, and dryer performance. |
The process generally proceeds in three stages: freezing, primary drying, and secondary drying. During freezing, controlled cooling converts water into ice and may also crystallize or vitrify solutes. In primary drying, the pressure is lowered below the triple point, and heat is supplied so ice sublimes directly to vapor. Secondary drying removes water that remains bound to the solid matrix, yielding a low final water content. Product temperature must stay below the collapse or glass transition temperature to maintain structure. Cycle design therefore balances shelf temperature, chamber pressure, and time.
Freeze-drying is used for materials whose activity or structure depends on low temperature and low water content. Examples include certain biologics, diagnostic reagents, starter cultures, coffee, and porous inorganic precursors. The dried product forms a cake whose porosity aids rapid wetting and dissolution. Main drawbacks are high energy use, long cycle times, and sensitivity to formulation and equipment variation. Questions remain about how freezing rates and ice morphology affect batch uniformity, especially when moving from laboratory to production scale.
Lyophilization, also called freeze-drying, is a dehydration process in which a solvent, usually water, is frozen and then removed by sublimation under reduced pressure. The method preserves heat-sensitive materials that would degrade in conventional drying. Large-scale use grew during the mid-twentieth century for blood plasma and antibiotics, and it later expanded to vaccines, enzymes, foods, and advanced materials. The process produces a dry, porous solid that usually reconstitutes rapidly. It is distinct from simple evaporation because the solvent bypasses the liquid phase during primary removal.
Secondary drying removes bound water that remains after ice sublimation. Shelf temperature is raised gradually while pressure remains low, reducing water content to a target range. Over-drying can cause brittleness or electrostatic issues, while under-drying affects stability. The endpoint is often judged by pressure rise tests, temperature measurements, or water content analysis. Scale-up depends on matching heat and mass transfer across equipment sizes. Small changes in shelf temperature or pressure can alter cycle length substantially.
Lyophilization, or freeze-drying, removes water from a material by freezing it and then lowering pressure so ice changes directly to vapor. The process relies on sublimation, the phase transition from solid to gas without an intervening liquid state. It is used for heat-sensitive materials that would degrade in conventional drying. The three stages are freezing, primary drying, and secondary drying, each with distinct temperature and pressure requirements. In practice, cycle design balances these variables.
After primary drying, secondary drying removes water that remains bound to the material. This stage raises the shelf temperature while maintaining low pressure, which encourages desorption of unfrozen water. Residual moisture can be reduced to a low percentage, improving stability for many products. The process parameters, including freezing rate, shelf temperature, and chamber pressure, influence the final pore structure and reconstitution behavior. Control of these variables helps prevent collapse or meltback during drying.
A formulation often contains excipients that protect the active ingredient during freezing and drying. Bulking agents provide structure, while lyoprotectants stabilize sensitive molecules. The freezing step can produce ice crystals whose size and distribution affect the drying rate, and cycle design includes freezing, annealing, and drying phases. If the product temperature rises above a critical value, the cake may collapse or lose its porous structure. Successful lyophilization therefore depends on the interaction between formulation, equipment, and cycle design.
The physics of lyophilization couples heat transfer, mass transfer, and phase behavior. Sublimation requires a vapor pressure difference between the ice front and the chamber, and the dried layer adds resistance to vapor flow. Amorphous formulations are characterized by a glass transition temperature of the maximally freeze-concentrated solute, often denoted Tg'. Crystalline bulking agents can provide structure, while amorphous excipients stabilize labile components. Open questions remain about spatial heterogeneity, edge effects, and how laboratory cycles scale to production.
Lyophilization is a drying process in which a solvent, usually water, is removed from a frozen material by sublimation under reduced pressure. The material is first solidified, then placed under vacuum so that ice transitions directly to vapor without a bulk liquid phase. This approach suits heat-sensitive substances that would degrade during conventional evaporation. Primary drying removes unbound ice, while secondary drying reduces water that remains adsorbed to the solid matrix. The result is a porous, lightweight solid that can be reconstituted later.
Yeast estrogen screen (YES) and Yeast androgen screen (YAS) are in vitro screens that have been developed in order to detect estrogenic and androgenic activities, respectively, of natural and synthetic compounds, mixtures and environmental samples. The test is based on genetically modified yeast cells (Saccharomyces cerevisiae), which contain the gene for the human estrogen or androgen receptor coupled to a reporter gene (e.g. lacZ). Activation of the receptor initiates a cascade of events leading to the expression of the reporter gene product (e.g. β-galactosidase) which converts a substrate (e.g. CPRG) which leads to a measurable color change from yellow to red in the medium. Alternative systems are based on the generation of a luminescence signal. Activating (agonistic) samples can be measured directly; inhibiting (antagonistic) activities are measured as the reduction of color development in the presence of a known activating substance.
The most prominent natural toxin groups that exist in aquatic environments are mycotoxins, algal toxins, bacterial toxins, and plant toxins (8). These marine biotoxins are dangerous to human health and have been widely studied due to their high potential to bioaccumulate in edible parts of seafood. Autotrophic bacteria and algae are unrelated organisms; however, in aquatic environments, they are both primary producers. Cyanobacteria are an important autotrophic bacteria in the water food web. Explosions of cyanobacteria known as algal blooms can produce cyanotoxins harmful to both the ecosystem and human health. These harmful algal blooms are more likely to be produced at a dangerous amount when there is an excess of nutrients, the temperature is 20 °C, there is more light, and calmer waters. Eutrophication and other contamination can lead to an environment that promotes cyanobacteria blooms. Processes that promote an excess of nutrients, and human activities, such as agricultural runoff and sewage overflows, are primarily responsible. Other factors include algal species and grazers being in higher concentrations, allowing for an abundance of cyanobacterial organisms that are associated with the production of toxins. Detection of the extent of an algal bloom begins by taking samples of water at various depths and locations in the bloom.
24. Adv Gerontol. 2008;21(1):68-73. [Biological activity of regulatory peptides in model experiments in vitro]. [Article in Russian] Kozina LS, Arutiunian AV, Stvolinskiĭ SL, Khavinson VKh. Biological effects of short regulatory peptides, pinealon, vesugen, vilon and epitalon were studied in model experiments in vitro. These peptides were found not to demonstrate direct antioxidant activity but be able to restrict lipid peroxidation of human lipoproteins by modification of their structure. The short peptides increase stability of red blood cell membranes toward osmotic hemolysis. They also elevate the stationary level of intracellular reactive oxygen species and at the same time decrease (all excepting epitalon) percent of dead cells in neuronal population. The suggestion was made that under in vivo conditions, short peptides may participate in apoptosis/necrosis regulation.
Anti-obesity medication or weight loss medications are pharmacological agents that reduce excess body fat and cause weight loss. These medications alter one of the fundamental processes of weight regulation, by: reducing appetite and consequently energy intake, increasing energy expenditure, redirecting nutrients from adipose to lean tissue, or interfering with the absorption of calories. Weight loss drugs have been developed since the early twentieth century, and many have been banned or withdrawn from the market due to adverse effects, including deaths; other drugs proved ineffective. Although many earlier drugs were stimulants such as amphetamines, in the early 2020s, GLP-1 receptor agonists became popular for weight loss. As of 2023, the medications liraglutide, naltrexone/bupropion, orlistat, semaglutide, tirzepatide and phentermine/topiramate are approved by the US Food and Drug Administration (FDA) for weight management in combination with reduced-calorie diet and increased physical activity. Medications to treat obesity may be considered in those with a body mass index above 30, or above 27 with obesity related complications (such as hypertension, hyperlipidemia, cardiovascular disease, or obstructive sleep apnea). As of 2022, no medication has been shown to be as effective at long-term weight reduction as bariatric surgery.
Biopolymers are natural polymers produced by the cells of living organisms. Like other polymers, biopolymers consist of monomeric units that are covalently bonded in chains to form larger molecules. There are three main classes of biopolymers, classified according to the monomers used and the structure of the biopolymer formed: polynucleotides, polypeptides, and polysaccharides. The polynucleotides, RNA and DNA, are long polymers of nucleotides. Polypeptides include proteins and shorter polymers of amino acids; some major examples include collagen, actin, and fibrin. Polysaccharides are linear or branched chains of sugar carbohydrates; examples include starch, cellulose, and alginate. Other examples of biopolymers include natural rubbers (polymers of isoprene), suberin and lignin (complex polyphenolic polymers), cutin and cutan (complex polymers of long-chain fatty acids), melanin, and polyhydroxyalkanoates (PHAs).
Sources: en.wikipedia.org
Actin-binding proteins (also known as ABPs) are proteins that bind to actin. This may mean ability to bind actin monomers, or polymers, or both. Many actin-binding proteins, including α-actinin, β-spectrin, dystrophin, utrophin and fimbrin, do this through the actin-binding calponin homology domain. This is a list of actin-binding proteins in alphabetical order. 25kDa 25kDa ABP from aorta 30akDA 30bkDa 34kDA 45kDa 110 kD dimer ABP 110 kD (Drebrin) p53 p58gag p185neu p116rip a-actinin Abl ABLIM Actin-Interacting MAPKKK Ssk2p ABP120 ABP140 Abp1p ABP280 (Filamin) ABP50 (EF-1a) Acan 125 (Carmil) ActA Actibind Actin Actinfilin Actinogelin Actin-regulating kinases Actin-Related Proteins Actobindin Actolinkin Actopaxin Actophorin Acumentin (= L-plastin) Adducin ADF/Cofilin Adseverin (scinderin) Afadin AFAP-110 Affixin Aginactin AIP1 Aldolase Angiogenin Anillin Annexins Aplyronine Archvillin (isoform of Supervillin) Arginine kinase Arp2/3 complex Band 4.1 Band 4.9 (Dematin) b-actinin b-Cap73 Bifocal Bistramide A BPAG1 Brevin (Gelsolin)
It is important for MADD patients to maintain strength and fitness without exercising or working to exhaustion. Learning this balance may be more difficult than normally, as muscle pain and fatigue may be perceived differently from normal individuals. Symptomatic relief from the effects of MADD may sometimes be achieved by administering ribose orally at a dose of approximately 10 grams per 100 pounds (0.2 g/kg) of body weight per day, and exercise modulation as appropriate. Taken hourly, ribose provides a direct but limited source of energy for the cells. Patients with myoadenylate deaminase deficiency do not retain ribose during heavy exercise, so supplementation may be required to rebuild levels of ATP. Creatine monohydrate could also be helpful for AMPD patients, as it provides an alternative source of energy for anaerobic muscle tissue and was found to be helpful in the treatment of other, unrelated muscular myopathies. Inborn Errors of Metabolism Metabolic Myopathies Purine Nucleotide Cycle
January 19 – March 25: 2018 FIBA Americas League San Lorenzo defeated Mogi das Cruzes, 79–71, to win their first FIBA Americas League title. Regatas Corrientes took third place. June 11 – 16: 2018 FIBA Under-18 Americas Championship in St. Catharines The United States defeated Canada, 113–74, to win their fifth consecutive and ninth overall FIBA Under-18 Americas Championship title. Argentina took third place. August 1 – 7: 2018 FIBA Under-18 Women's Americas Championship in Mexico City The United States defeated Canada, 84–60, to win their ninth consecutive and tenth overall FIBA Under-18 Women's Americas Championship title. Argentina took third place.
Because of the mild elution conditions (biotin plus wash buffer) SBP-Tagged proteins can be generated in a relatively pure state with a single purification step. There are several relatively abundant mammalian proteins that inherently associate with the IMAC matrices that bind to the more commonly used Polyhistidine-tag (His-tag). For this reason non-IMAC purification protocols, including with the SBP-Tag, are often preferred for proteins that are expressed in mammalian cells.
Sources: en.wikipedia.org
In the phosphatidylinositol signal pathway, the extracellular signal molecule binds with the G-protein receptor (Gq) on the cell surface and activates phospholipase C, which is located on the plasma membrane. The lipase hydrolyzes PIP2 into two second messengers: inositol 1,4,5-trisphosphate (IP3) and diacylglycerol (DAG). IP3 binds with the IP3 receptor in the membrane of the smooth endoplasmic reticulum and mitochondria to open Ca2+ channels. DAG helps activate protein kinase C (PKC), which phosphorylates many other proteins, changing their catalytic activities, leading to cellular responses. The effects of Ca2+ are also remarkable: it cooperates with DAG in activating PKC and can activate the CaM kinase pathway, in which calcium-modulated protein calmodulin (CaM) binds Ca2+, undergoes a change in conformation, and activates CaM kinase II, which has unique ability to increase its binding affinity to CaM by autophosphorylation, making CaM unavailable for the activation of other enzymes. The kinase then phosphorylates target enzymes, regulating their activities. The two signal pathways are connected together by Ca2+-CaM, which is also a regulatory subunit of adenylyl cyclase and phosphodiesterase in the cAMP signal pathway.
MAAs are widespread in the microbial world and have been reported in many microorganisms including heterotrophic bacteria, cyanobacteria, microalgae, ascomycetous and basidiomycetous fungi, as well as some multicellular organisms such as macroalgae and marine animals. Most research done on MAAs is on their light absorbing and radiation protecting properties. The first thorough description of MAAs was done in cyanobacteria living in a high UV radiation environment. The major unifying characteristic among all MAAs is UV light absorption. All MAAs absorb UV light that can be destructive to biological molecules (DNA, proteins, etc.). Though most MAA research is done on their photo-protective capabilities, they are also considered to be multi-functional secondary metabolites that have many cellular functions. MAAs are effective antioxidant molecules and are able to stabilize free radicals within their ring structure. In addition to protecting cells from mutation via UV radiation and free radicals, MAAs are able to boost cellular tolerance to desiccation, salt stress, and heat stress.
Bruce Glick grew up in Pittsburgh, Pennsylvania and was interested in birds as a child. His father, Peter Glick, was the Secretary of Labor for Pennsylvania. Glick served in World War II. He went to Rutgers University and studied birds majoring in poultry science, graduating in 1951. In 1950 he married Kay McCall. He received an M.S. degree from the University of Massachusetts in genetics in 1952 and attended Ohio State University as a Ph.D. student, graduating with a PhD in physiology in 1955. While there, he worked on determining the purpose of the Bursa of Fabricius, a gland that he was able to remove from a goose without any apparent effect. A fellow graduate student, Timothy Chang, worked with Glick's geese in a different study, and noticed that the birds without the Bursa of Fabricius did not produce expected antibodies. Glick and Chang wrote up the results of this study and were unable to get it published in Science, so it was published in Poultry Science in 1956. Their publication, considered a landmark paper, is one of the most cited works from Poultry Science.
The American Journal of Respiratory Cell and Molecular Biology is a monthly peer-reviewed medical journal and an official publication of the American Thoracic Society. It covers research on the structure and function of the respiratory system under physiologic and pathophysiologic conditions. It was established in July 1989. The founding editors-in-chief were Jerome S. Brody, Robert M. Senior, and Mary C. Williams. John A. Mcdonald served as editor from 1993 to 1998. Kenneth B. Adler (North Carolina State University) served as editor from 2009 to 2016. Paul Schumacker (Northwestern University) served as editor from October 1, 2016, to October 21, 2023. Andrew Halayko (University of Manitoba) assumed the editorship on November 1, 2023. The journal is abstracted and indexed in BIOSIS Previews, Current Contents/Life Sciences, Current Contents/Critical Care Medicine, Embase, Index Medicus/MEDLINE/PubMed, Science Citation Index Expanded, and Scopus. According to the Journal Citation Reports, the journal has a 2024 impact factor of 5.3. Official website
For SNP annotation, many kinds of genetic and genomic information are used. Based on the different features used by each annotation tool, SNP annotation methods may be split roughly into the following categories: Genomic information from surrounding genomic elements is among the most useful information for interpreting the biological function of an observed variant. Information from a known gene is used as a reference to indicate whether the observed variant resides in or near a gene and if it has the potential to disrupt the protein sequence and its function. Gene based annotation is based on the fact that non-synonymous mutations can alter the protein sequence and that splice site mutation may disrupt the transcript splicing pattern.
Sources: en.wikipedia.org
The main change is sublimation, in which ice becomes water vapor without melting into liquid water. This occurs when the chamber pressure is held below the vapor pressure of ice while mild heat is supplied. The result is a dry, porous solid that retains much of its original shape.
Freezing determines ice crystal size, solute distribution, and the pore network left after drying. A slow or fast freezing rate can produce different cake structures and affect reconstitution. It also sets whether the formulation follows an amorphous or crystalline drying path.
It removes most free water during primary drying and part of the bound water during secondary drying. A small residual moisture content often remains and is specified for each product. Complete removal is generally neither practical nor desirable for stability.
Simple drying usually removes water by evaporation from a liquid or solid, often with heat. Lyophilization first freezes the material and then removes ice by sublimation under vacuum. This avoids prolonged exposure to liquid water and high temperatures.